Aiuto Flash Nokia 6630

[giubbam]

Salve, sono un nuovo iscritto e mi serve una mano con il mio Nokia 6630,
vi spiego tutto...in pratika io ho comprato un NOKIA 6630 brandizzato Tim e sikkome ho la skeda wind...volevo metterci un NOBRAND x togliere tutta la roba Tim,
ora su un altro forum un moderatore mi ha spiegato passo passo tutto ciò ke devo fare xò ho avuto un problema...e cioè...quando vado a FLASHARE il cell al 97% mi esce una skermata ke dice questo:

Communication to product not working!


Corrective Action:
1. Remove charger if connected.
2. Remove battery.
3. Install battery back.
4. Boot up the phone to normal mode from power key by keeping also the buttons green call button,
number 3 button and star button pressed and keep those buttons pressed until you see the hands or PIN query on the screen.
5. Connect charger if needed.
6. Enter PIN code if requested.
7. Set home country, time and date if requested.
8. Wait until the phone is booted up to normal mode.
9 Press OK => flashing will continue



PNMsgIO: No message(s) received in given time;MTI32=0x80042007

CMsgBase::WaitMtiMsg32:MTI32,'Timeout';MTI=0x80042007
CMsgBase::WaitMtiMsg:MTI32,'Timeout';MTI=0x80042007
MsgInfoVerRead;MTI=0x80042007
CPcfPhoneInfo::PcfInfoVerRead, 'MTI error';PCF = 0x80041009

GetProductType: Checking product failed.;CAmsFlashFN=0x80041009


cioè in pratika dice ke non riesce a comunicare con il Cell...mi sapete dire kome mai?
kosa devo fare?:-(
spero in una vostra risposta...
grazie anticipatamente...



..........G | |_| b B @ ][\/][..........

[fokozuynen]

. Prima ai bisognio di Phoenix internal programa
e puoi io ti do una solutione in inglese se non lo capisci batti un colpo )



Setting up the connection:
To allow the flashing of a dead phone, the used connection must be set to
‘NO CONNECTION’. To do this, go to File -> Manage Connection
In the window ‘Manage Connection’, highlight the ‘NO CONNECTIONS’ bar
and set it at the first place of the priority list.
Press ‘Apply’ button and then close the ‘Manage Connection’ window.
2. Setting the product name:
Open the product ‘RM-78’ using the menu File -> Open Product
3. Flashing the phone
To perform the flashing, proceed as follows:
- Choose menu ‘Flashing -> Firmware update’
- Activate button ‘Dead Phone USB flashing’
- Choose the variant to be flashed
Press ‘Start’ button
The flashing starts. After a few seconds the message ‘Cmt->Waiting USB
device (1 of 30). Press phone’s power button’ appears.
Press the phone’s power button. The flashing will be performed

When it is OK then
Carrying out firmware update:
1. Setting up the connection
To allow the flashing of a dead phone, the used connection must be set to
‘USB’. To do this, go to: File -> Manage Connection. In the window ‘Manage
Connection’, highlight the ‘USB’ bar and set it at the first place on the priority
list.
Press ‘Apply’ button and then close the ‘Manage Connection’ window.
2. Scan the product and start the flashing
- Unplug the USB cable, if it has been plugged in before
- Power on the phone with the USB cable unplugged
- Plug the USB cable
- Scan the product by using Crtl-R key combination or going to ‘File -> Scan
Product’
- After successful scanning of the product, go to ‘Flashing -> Firmware
Update’
- Choose between ‘Restore User Product’ or ‘Phone As Manufactured /
Refurbish’ and press ‘Start’ button
After a couple of seconds the message ‘Mode change’ appears on the
‘Firmware Update’ window. In the meanwhile, the message ‘Start up phone
without SIM card?’ appears on the mobile phone’s display. On the mobile
phone side, press on the ‘Accept’ button to confirm the phone’s start. The
flashing goes on. After a while the flashing is finished.

[Trespolo69]

Vorrei sbrandizzare il 6630m della TIM: mi sapete dire dove trovare il software necessario (e come usarlo?) Grazie